Light-motion HC3 Instrukcja Użytkownika

Bluefin HC3 Owner’s Manualwww.uwimaging.comFor the Sony HDR-HC3 camcorder

10Rear Plate (Refer fig. 15)On/Mode - Turns the camcorder on and cycles through modes.Housing Left Side (Refer fig. 16 and 17)Manual - Activates the c

11Smooth Slow Recording Set up the P-Menu as described in this manual under P-Menu Setup.Before loading the camera into the housing set the mode for t

12Lens Installation / RemovalTo Install Lens1. Perform o-ring inspection.2. Align lens to housing details.3. Press lens into housing.4. Rotate clockwi

13Bluefin Monitors - Getting StartedIllustrated below are the components of the Compact Monitor and the RemoteMonitor. Take time to identify and becom

14Bluefin Monitor - Bulkhead Installation1) Remove the Rear Plate.2) Using a flat head screwdriver or coin, remove the Port Plug. (Refer Fig. 16)3) On

15Compact Monitor OperationPower On/OffThe monitor will power on and off with the camcorder.Remote Monitor Operation1) If necessary, activate power to

16Charging the Remote and Compact Monitor1) Remove the Charging Port Plug using a coin or large flat head screwdriver.(Refer fig. 20)2) Plug charger i

17Bluefin Light Systems - Getting StartedPictured below are the components of the Sunray-S Mini Pro and Sunray-S Mini Elitelighting system. Take a mom

18Charging BatteriesIt is recommended that you charge your batteries when they arereceived. It is also recommended to charge batteries just priorto us

19Mounting Battery Pods1) Remove the rear plate of the housing.2) Slide the battery pods into housing channels.3) Insert Pod Locker between the pods a

WelcomeCongratulations on your purchase of the Bluefin underwater video housing.Please inspect the packaging of your product to verify that there was

20(Fig. 25) (Fig. 26)(Fig. 27) (Fig. 28)1) Using an allen key, remove the two screws on the back of the handle.(Refer fig. 25)2) Remove the Handle Cap

21First Time UseAll Light & Motion equipment is pressure tested prior toshipping. However, there could be unseen damage due toshipping. A test div

Rear Plate O-rings Smart Grip O-ring Optic O-rings4) To check O-rings for damage, place the O-ring between the index finger and thumb.Then pull the O-

Bluefin AccessoriesBluefin Two-Year Fault Free Warranty . . . . . . . . . . . . . .905-0201Bluefin Super Macro Lens . . . . . . . . . . . . . . . . .

Light & Motion300 Cannery Row • Monterey, CA 93940(831) 645-1525 • Fax (831) 375-2517www.uwimaging.com905-0266-A

3Table of ContentsGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4Getting StartedIllustrated below are the locations of Bluefin’s features and functions.Take time tofamiliarize yourself with the housing.Monitor Base

5Camera Preparation1. Install a fully charged Sony NP-FP90 battery.2. Install a HD DVC tape into your camcorder.3. If still images are desired, instal

6P-Menu SetupThe P-Menu is a customizable menu that allows quick access to commonly usedcamera features.This is very useful underwater since controls

7(Fig. 5) (Fig. 6)(Fig. 7) (Fig. 8)

8Mounting the Camera1. Remove the rear plate by pushing the Latch Lock in and rotating the latch downand forward of the housing body. (Refer fig. 9)2.

9and that the O-rings seat evenly.OperationLeft Smart Grip Controls (Refer fig. 12)Far - Moves focus point further from camcorder.Near - Moves focus p